|
>>
Release Agents for Moldmaking and Casting
|
|
|
 |
| One Step® Release Agent And Sealer - One Product, Two Jobs! |
One Step™ Release Agent And Sealer - One Product, Two Jobs!
 |
One Step® is a convenient, economical liquid sealing agent and release agent in one. This non-flammable, non-VOC formula is offered as a "one step" alternative to using a sealing agent followed by a release agent during the mold making process using Smooth-On urethane mold rubbers.
One Step® will facilitate the release of cured urethane mold rubber from plaster, concrete, stone, brick, marble, limestone, wood, metal and other surfaces. Do not use on modeling clays. |
|
|
|
| Ease Release® 200 and 205 |
Ease Release® 200 and 205
|
Ease Release® 200 and 205 is an excellent general purpose release agent for making molds and casting parts. This product will release urethane rubber, urethane resins, polyester resins, RTV silicones, and thermoplastic polymers. Ease Release® 200 and 205 is effective on urethane, silicone and metal molds.
Ideal For Releasing:
~ Urethane Rubber From Original Models
~ Urethane Plastic From Urethane Rubber
~ Silicone Rubber From Original Models
~ Silicone Rubber From Silicone Rubber
~ Urethane Plastic From Silicone Rubber
205 is a liquid version, 200 is an aerosol. Looking for a different Mann product? View the Mann mold release agent product line.
|
|
|
|
| Universal Mold Release |
Universal Mold Release
|
Universal Mold Release® is formulated especially for mold making and casting, and works well with most liquid rubber and liquid plastic products. It will release mold rubbers (such as polyurethanes and polysulfides) from properly prepared models. Sealing porous models (wood, plaster, concrete) or certain modeling clays (containing water or sulfur) with Smooth-On SuperSeal® or other sealer may be necessary. If using silicone rubber, seal model surface with SuperSeal® only. Do not use UMR.UMR also easily releases a variety of casting materials (epoxies, Smooth-On liquid plastics, etc.) from cured rubber molds. Properly used, Universal Mold Release improves molding efficiency for a variety of casting applications and will actually lengthen the life of your production mold.
Available in aerosol or bulk liquid. |
|
|
|
| In & Out® Concrete Release Agent |
In & Out® Concrete Release Agent
|
IN & OUT® II water soluble release agent will aid in releasing concrete or gypsum plaster castings from Smooth-On rubber molds. IN & OUT® II provides a clean, positive release and does not interfere with or affect surface detail and helps minimize air bubbles in finished castings. Simplify Your Production Casting With IN & OUT II®
- Will Not Stain / Soften Concrete Or Gypsum Surfaces
- Mix With Water - Economical
- Will Not Affect Color Pigmenting Of Cast Concrete
- Minimizes “Bug Holes” In Concrete And Air Bubbles In Gypsum Castings
- Keeps Molds Clean - Does Not Build Up
- Significantly Extends Mold Life
IN & OUT® II IS DILUTED WITH WATER. Mix 4 parts water to 1 part In & Out® II. Mixing can be done by hand or slow speed mixer. Do not shake or agitate as this may cause product to foam. How you dilute IN & OUT® II (amount mixed with water, coverage and frequency of application) will depend on the concrete aggregate mix and the form material you are casting into. For example, when casting concrete with a low grit/high sand content (minimal abrasion) into a polyurethane mold, the mix ratio of water to IN & OUT II® can be 4 : 1. High grit content may call for a dilution ratio of 2 parts water to 1 part release agent. Mix only amount needed for one day. Mixture may separate after 24 hours. Re-mix to a uniform consistency and apply. |
|
|
|
|
|
|
|
|
|
Material Calculatorand Unit Convertor
Custom Formulating
Newsletter Signup
