Creating a "Glue Shim" to Help Deal with a Difficult Original Model

Creating a "Glue Shim" to Help Deal with a Difficult Original Model

Customers often contact Smooth-On with specific mold making questions. One of the most common questions we're asked is how to create a mold from an original model that has a pass-through -- essentially a hole created by the configuration of the piece. Standing figures often have one or more of these pass-through's, usually between the legs or arms of the piece. If the mold rubber is simply poured over the original model, it will fill these voids and completely encapsulate the piece in a solid block of rubber. The original model would then have to be cut out of the mold rubber, which can be very difficult and is often imprecise.

In this photo sequence, we demonstrate another strategy for dealing with a common type of pass-through. This advanced mold making technique involves creating a “glue shim” that eliminates the need to cut the rubber away from the voids in the original model. Smooth-On’s SORTA-Clear® 40 silicone mold rubber is used to make the process even easier.

SORTA-Clear® 40 is a premium water white translucent silicone rubber (platinum catalyst) that cures at room temperature with negligible shrinkage. SORTA-Clear® 40 has a Shore hardness of 40A and features exceptional tear and tensile strength.

1 - The original model stands approximately 12'' (30 cm) tall and is made of unglazed ceramic. The two openings, or ''pass-through's'' on this piece create a mold making challenge.	2 - If these pass-through's are not addressed, the mold making rubber will encapsulate the piece and lock it within a solid block of rubber. Creating a glue shim eliminates the need to hand cut the silicone in these spots - a process that can be difficult and imprecise.	3 - Prior to creating the glue shims, the piece should be sealed. Smooth-On's Super Seal® is perfect for sealing the unglazed ceramic original.
4 - Super Seal® is a very low viscosity sealer that can be brushed onto the original without distorting the details of the piece.	5 - A minimum of two coats of Super Seal® is recommended to ensure thorough coverage.	6 - The first step to creating the glue shim is to have a base onto which the epoxy can be applied. Begin by taking a portion of water clay and wrapping it tightly in plastic wrap.
7 - Position the plastic wrapped clay behind on on side of the pass-through.	8 - Push the clay into the gap. The clay will conform to the shape of the pass-through and fill the void.	9 - Push the clay into any corners or small gaps around the perimeter of the pass-through.
10 - Once the clay has been pushed into all areas, lay the piece down flat in preparation for applying the epoxy glue shim. Smooth-On's Super Instant Epoxy is a very fast setting epoxy, perfect for this type of application.	11 - Super Instant Epoxy is a two component epoxy that is mixed 1:1 by volume. Dispense a small amount of Part A.	12 - Dispense an equal amount of Part B.
13 - Mix parts A and B thoroughly. Super Instant Epoxy has a very short working time - 2.5 minutes. It is important to keep this limited working time in mind when using the epoxy. Do not mix more than can be applied in this timeframe.	14 - Using an acid brush, spread a thin layer of Super Instant over the plastic-wrapped clay.	15 - Using a tongue depressor, the Super Instant is spread carefully along the edges and into the corners of the void. The goal is to completely fill the gap, leaving an airtight film of Super Instant.
16 - Another portion of clay is covered tightly in plastic wrap.	17 - This plastic-wrapped clay is pressed into the gap under the arm on the model.	18 - The application of Super Instant is repeated and the area under the arm is filled in.
19 - Super Instant Epoxy is a very fast setting material. It has a 2.5 minute working time and cures to handling strength in 5-10 minutes. After this period, the plastic wrapped clay can be carefully peeled away from the cured Super Instant. The Super Instant will not stick to the plastic wrap and the thin film will remain in place.	20 - Super Instant Epoxy is a very fast setting material. It has a 2.5 minute working time and cures to handling strength in 5-10 minutes. After this period, the plastic wrapped clay can be carefully peeled away from the cured Super Instant. The Super Instant will not stick to the plastic wrap and the thin film will remain in place.	21 - Once the Super Instant Epoxy has fully cured, the model is ready to for the mold making process.
22 - The model is secured to a melamine board base using hot melt glue.	23 - The model is secured to a melamine board base using hot melt glue.	24 - More melamine board is cut to size to make a mold box.
25 - The mold box is secured to the melamine base with more hot melt glue.	26 - Important: Carefully read the technical bulletin and material safety data sheet prior to working with any material. These documents provide important information that will help make you mold making project a success.	27 - For this project, Smooth-On's SORTA-Clear® 40 is used. This material has a 100A:10B by weight mixing ratio. Using an accurate gram scale, Part A is measured out.
28 - Prior to measuring Part B, it is important to shake or stir the material thoroughly.	29 - Using an accurate gram scale, Part B is measured out.	30 - Parts A and B are combined.
31 - The material is thoroughly mixed, following the instructions outlined on the technical bulletin.	32 - For best results, and to eliminate the most air bubbles from the thick silicone rubber, SORTA-Clear® 40 is vacuum degassed.	33 - Vacuuming the material should be done at 29 h.g.
34 - SORTA-Clear® 40 silicone is slowly poured over the original figurine in the mold box.	35 - SORTA-Clear® 40 should be poured until the top of the model is covered with at least 1/2'' (1.25 cm) of mold rubber. The SORTA-Clear® 40 is allowed to fully cure (16 hours) prior to demolding.	36 - Once the SORTA-Clear® 40 has cured, the mold box can be removed.
37 - The box walls are pulled away from the mold.	38 - The mold is removed from the baseboard. SORTA-Clear® 40 is clear enough that the original model can be easily seen within the solid block of rubber. This unique property of SORTA-Clear® becomes important when removing the original model from the mold.	39 - The translucent rubber is cut with a razor knife to allow for removal of the original piece. SORTA-Clear® makes precision cutting around an original much easier.
40 - Once the mold has been cut down one side, the rubber is spread apart and the original model is removed.	41 - The completed mold, ready for casting.	42 - The mold is banded together and Smooth-Cast® 300 resin is poured in. The resin is tinted slightly with SO-Strong® black.
43 - Once the Smooth-Cast® 300 has cured (approximately 10 minutes) it is removed from the mold.	44 - The casting reflects perfect detail captured from the original model. Using a glue shim will leave a very thin layer of plastic flashing within the pass-through's.	45 - The plastic flashing is very thin and brittle. It can be easily removed with a razor knife, and then sanded smooth for a seamless casting.