Compare Tool

Vs.
remove

TASK™ 7

TASK™ 7 vs. EZ-Spray® Silicone 22EZ-Spray® Silicone 22

Flame Resistant Urethane Resin

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Resins
Mixed Viscosity11,000 cps200 cps
Pot Life5 minutes2.5 minutes
Cure Time45 minutes10 minutes
Shore D Hardness73
Shore A Hardness22
ColorTranslucent GreenWhite
Tensile Strength490 psi3,390 psi
Elongation @ Break450 %15.1 %
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22TASK™ 7
Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Resins
Mixed Viscosity11,000 cps200 cps
Mix Ratio By Volume1A:1B1A:1B
Mix Ratio By Weight104A:100B
Pot Life5 minutes2.5 minutes
Cure Time45 minutes10 minutes
Shore D Hardness73
Shore A Hardness22
Specific Gravity1.08 g/cc1.2 g/cc
Specific Volume25.6 cu. in./lb.23.1 cu. in./lb.
ColorTranslucent GreenWhite
Die B Tear Strength102 pli
Tensile Strength490 psi3,390 psi
Tensile Modulus150,700 psi
Elongation @ Break450 %15.1 %
100% Modulus49 psi
Compressive Strength5,140 psi
Compressive Modulus57,600 psi
Flexural Strength5,450 psi
Flexural Modulus148,900 psi
Shrinkage<.001 in. / in.0.0111 in. / in.
Heat Deflection Temp131 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

TASK™ 7

Flame Out™ is a low viscosity, fast set casting resin that meets UL 94 V-O requirements for flame resistance. It does not contain mercury, TDI or MOCA. Mix ratio is 1A:1B by volume. Pot life is 2.5 min. and demold time is 10 min. at 73°F / 23°C (depending on mass).

Fully cured Flame Out™ material is tough, durable, machinable and paintable. It has much higher physical and performance properties than any other flame rated urethane available anywhere. Vibrant colors and color effects are possible by adding SO-Strong™ color tints. Applications for Flame Out™ include making flame resistant prototype and architectural models, model toys, theme park and stage elements, durable miniatures and special effect props. Material can also be used for potting and encapsulation applications.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›