Compare Tool

Vs.
remove

FOAM-iT!™ 10 SLOW

FOAM-iT!™ 10 SLOW vs. EZ-Spray® Silicone 22EZ-Spray® Silicone 22

Rigid Urethane Expanding Foams

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Mix and Pour Expanding Foams
Mixed Viscosity11,000 cps400 cps
Pot Life5 minutes3.5 minutes
Cure Time45 minutes4 hours
Shore A Hardness22
Specific Volume25.6 cu. in./lb.157 cu. in./lb.
ColorTranslucent GreenBeige
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22FOAM-iT!™ 10 SLOW
Product Type
  • Silicone Rubber - Platinum Cure
  • Mix and Pour Expanding Foams
Mixed Viscosity11,000 cps400 cps
Mix Ratio By Volume1A:1B1A:1B
Mix Ratio By Weight100A:87B
Pot Life5 minutes3.5 minutes
Tack Free Time1 hour
Cure Time45 minutes4 hours
Shore A Hardness22
Expansion (approximate)6 times
Foam Density10 lb/ft³
Specific Gravity1.08 g/cc0.16 g/cc
Specific Volume25.6 cu. in./lb.157 cu. in./lb.
ColorTranslucent GreenBeige
Die B Tear Strength102 pli
Tensile Strength490 psi
Elongation @ Break450 %
100% Modulus49 psi
Shrinkage<.001 in. / in.
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

FOAM-iT!™ 10 SLOW

Smooth-On’s FOAM-iT!™ Series are two-component water blown rigid foams that are versatile and easy to use. FOAM-iT!™ products are available in 3lb., 4 lb., 5 lb., 8 lb., 10 lb.,15 lb. or 26 lb. per cubic foot densities. Parts A and B are measured and mixed in equal amounts by volume. The mixture is then poured into a mold or other form (apply release agent if necessary). The mixture will expand many times original volume (depending on which FOAM-iT!™ product you are using) and develop a uniform cell structure. FOAM-iT!™ 10 SLOW is a 10 lb. density foam with a long, 3.5 minute working time, taking 1 hour to reach handling strength and 4 hours to cure. FOAM-iT!™ 10 SLOW is designed for large-pour industrial, art-related and special effects applications.

FOAM-iT!™ products can be used as a straight casting material, backfill material for hollow castings (adds structural strength) or as an encapsulation material, etc. They can be color pigmented with SO-Strong™, UVO™ or IGNITE™ colorants and are used for a variety of art/ craft, industrial design and special effects applications.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›