Compare Tool

Vs. Vs.
remove

Mold Max™ 14NV

Mold Max™ 14NV vs. EZ-Spray® Silicone 22 vs. EZ-Spray® FoamEZ-Spray® Silicone 22 versus EZ-Spray® Foam

Low Viscosity Tin-Cure Silicone Rubber

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Mix and Pour Expanding Foams
  • Silicone Rubber - Tin Cure
Mixed Viscosity11,000 cps400 cps7,500 cps
Mix Ratio By Volume1A:1B1A:1BN/A (gram scale required)
Pot Life5 minutes13 seconds40 minutes
Cure Time45 minutes10 minutes4 hours
Shore A Hardness2214
Specific Gravity1.08 g/cc0.128 g/cc1.12 g/cc
ColorTranslucent GreenTanWhite
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22EZ-Spray® FoamMold Max™ 14NV
Product Type
  • Silicone Rubber - Platinum Cure
  • Mix and Pour Expanding Foams
  • Silicone Rubber - Tin Cure
Mixed Viscosity11,000 cps400 cps7,500 cps
Mix Ratio By Volume1A:1B1A:1B
Mix Ratio By Weight100A:10B
Pot Life5 minutes13 seconds40 minutes
Tack Free Time2 minutes
Cure Time45 minutes10 minutes4 hours
Shore A Hardness2214
Expansion (approximate)7 times
Specific Gravity1.08 g/cc0.128 g/cc1.12 g/cc
Specific Volume25.6 cu. in./lb.24.7 cu. in./lb.
ColorTranslucent GreenTanWhite
Die B Tear Strength102 pli87 pli
Tensile Strength490 psi490 psi
Elongation @ Break450 %600 %
100% Modulus49 psi35 psi
Shrinkage<.001 in. / in.0.002 in. / in.
Useful Temperature (min)-65 °F-65 °F
Useful Temperature (max)500 °F400 °F
Dissipation Factor, 100Hz0.02
Volume Resistivity9.000000E+14 ohm/cm
Dielectric Strength>500 volts/mil
Thermal Conductivity0.21 W/M*K
Dielectric Constant, 100Hz3.4

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

EZ-Spray® Foam

EZ~Spray® Foam is a polyurethane foam compound that can be conveniently sprayed using Smooth-On’s EZ~Spray® Junior System. Foam cures quickly to strong, lightweight and impact resistant 8 lb. rigid foam that can be used for a variety of applications including making lightweight castings. Foam can also be sprayed over certain rubber mold configurations as a mother mold material. For more information, refer to SmoothOn’s EZ~Spray® Junior manual and video.

Read More

Mold Max™ 14NV

Mold Max™ 14NV is a Shore 14A tin-catalyzed silicone rubber that offers low viscosity, fast cure and long library life. Mold Max™ 14 NV does not require vacuum degassing. Mix ratio is 100A:10B by weight. Working time is 40 minutes and cure time is 4 hours at room temperature. Mold Max™ 14NV will reproduce the finest detail and is suitable for a variety of industrial and art related applications including making molds for reproducing prototypes, furniture, sculpture and architectural elements.

Mold Max™ 14NV can also be used to create movie special effects. Cure time can be reduced with Accel-T™ cure accelerator. Mold Max™ 14NV can be used to cast a variety of materials including concrete, wax, gypsum, low melt alloys/metals and urethane, epoxy or polyester resins.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›