Compare Tool

Vs. Vs.
remove

Smooth-Cast® 326

Smooth-Cast® 326 vs. EZ-Spray® Silicone 22 vs. EZ-Spray® FoamEZ-Spray® Silicone 22 versus EZ-Spray® Foam

Ultra Low Viscosity Liquid Plastics

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Mix and Pour Expanding Foams
  • Urethane Resins
Mixed Viscosity11,000 cps400 cps100 cps
Pot Life5 minutes13 seconds9 minutes
Cure Time45 minutes10 minutes60 minutes
Shore D Hardness72
Shore A Hardness22
Specific Gravity1.08 g/cc0.128 g/cc1.07 g/cc
ColorTranslucent GreenTanClear Amber
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22EZ-Spray® FoamSmooth-Cast® 326
Product Type
  • Silicone Rubber - Platinum Cure
  • Mix and Pour Expanding Foams
  • Urethane Resins
Mixed Viscosity11,000 cps400 cps100 cps
Mix Ratio By Volume1A:1B1A:1B1A:1B
Mix Ratio By Weight115A:100B
Pot Life5 minutes13 seconds9 minutes
Tack Free Time2 minutes
Cure Time45 minutes10 minutes60 minutes
Shore D Hardness72
Shore A Hardness22
Expansion (approximate)7 times
Specific Gravity1.08 g/cc0.128 g/cc1.07 g/cc
Specific Volume25.6 cu. in./lb.25.9 cu. in./lb.
ColorTranslucent GreenTanClear Amber
Die B Tear Strength102 pli
Tensile Strength490 psi3,170 psi
Tensile Modulus140,000 psi
Elongation @ Break450 %10 %
100% Modulus49 psi
Compressive Strength3,080 psi
Compressive Modulus32,200 psi
Flexural Strength3,100 psi
Flexural Modulus95,700 psi
Shrinkage<.001 in. / in.0.0075 in. / in.
Heat Deflection Temp120 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

EZ-Spray® Foam

EZ~Spray® Foam is a polyurethane foam compound that can be conveniently sprayed using Smooth-On’s EZ~Spray® Junior System. Foam cures quickly to strong, lightweight and impact resistant 8 lb. rigid foam that can be used for a variety of applications including making lightweight castings. Foam can also be sprayed over certain rubber mold configurations as a mother mold material. For more information, refer to SmoothOn’s EZ~Spray® Junior manual and video.

Read More

Smooth-Cast® 326

The Smooth-Cast® 325, 326 & 327 ColorMatch® Series plastics are fast-cast resins that were developed specifically for adding color pigments and fillers to achieve true color representation or filler effect. The ColorMatch® Series is formulated “color neutral”. Small amounts of pigment will yield accurate, vivid colors from cured castings using So-Strong® tints or Ignite® color pigments. The ColorMatch® Series offers the convenience of a 1A: 1B mix ratio by volume and has a very low viscosity. Demold times range from about 10 minutes to 2-4 hours (depending on product, mass and mold configuration). Note: Large mass castings will get very hot and shrink more, depending on mold configuration.

The ColorMatch® Series also readily accept fillers (such as URE-FIL® 3 from Smooth-On). Applications for the ColorMatch® Series plastics include making pigmented prototype models or figures, special effect props, reproducing small to medium size sculptures, decorative jewelry, etc.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›