Compare Tool

Vs. Vs.

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Mix and Pour Expanding Foams
  • Urethane Resins
Mixed Viscosity11,000 cps400 cps100 cps
Pot Life5 minutes13 seconds5 minutes
Cure Time45 minutes10 minutes90 minutes
Shore D Hardness80
Shore A Hardness22
Specific Gravity1.08 g/cc0.128 g/cc1.09 g/cc
ColorTranslucent GreenTanBlack
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22EZ-Spray® FoamSmooth-Cast® ONYX™ SLOW
Product Type
  • Silicone Rubber - Platinum Cure
  • Mix and Pour Expanding Foams
  • Urethane Resins
Mixed Viscosity11,000 cps400 cps100 cps
Mix Ratio By Volume1A:1B1A:1B100A:100B
Mix Ratio By Weight120A:100B
Pot Life5 minutes13 seconds5 minutes
Tack Free Time2 minutes
Cure Time45 minutes10 minutes90 minutes
Shore D Hardness80
Shore A Hardness22
Expansion (approximate)7 times
Specific Gravity1.08 g/cc0.128 g/cc1.09 g/cc
Specific Volume25.6 cu. in./lb.27.7 cu. in./lb.
ColorTranslucent GreenTanBlack
Die B Tear Strength102 pli
Tensile Strength490 psi7,660 psi
Tensile Modulus374,000 psi
Elongation @ Break450 %3 %
100% Modulus49 psi
Compressive Strength11,400 psi
Compressive Modulus97,900 psi
Flexural Strength10,230 psi
Flexural Modulus286,000 psi
Shrinkage<.001 in. / in.0.012 in. / in.
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F
Heat Deflection With Post Cure212 °F

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

EZ-Spray® Foam

EZ~Spray® Foam is a polyurethane foam compound that can be conveniently sprayed using Smooth-On’s EZ~Spray® Junior System. Foam cures quickly to strong, lightweight and impact resistant 8 lb. rigid foam that can be used for a variety of applications including making lightweight castings. Foam can also be sprayed over certain rubber mold configurations as a mother mold material. For more information, refer to SmoothOn’s EZ~Spray® Junior manual and video.

Read More

Smooth-Cast® ONYX™ SLOW

Smooth-Cast® ONYX™ is a mercury-free urethane resin that cures at room temperature to a deep black, solid plastic. ONYX™ resins offer the convenience of a 1A:1B by volume mix ratio and have very low viscosities, so they are easy to mix and pour. ONYX™ resins have an ultimate Shore hardness of 80D and offer higher physical properties and higher heat resistance vs. other general purpose resins. ONYX™ resins are available in 2 speeds. ONYX™ SLOW resin has a pot life of 5 minutes and a cure time of 90 minutes.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›