Compare Tool

Vs.
remove

EpoxAmite™ 102

EpoxAmite™ 102 vs. EZ-Spray® Silicone 22EZ-Spray® Silicone 22

MEDIUM Cure Epoxy Laminating System

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
Mixed Viscosity11,000 cps650 cps
Pot Life5 minutes22 minutes
Cure Time45 minutes15 hours
Shore D Hardness80
Shore A Hardness22
ColorTranslucent GreenClear Yellow
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22EpoxAmite™ 102
Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
Mixed Viscosity11,000 cps650 cps
Mix Ratio By Volume1A:1B3A:1B
Mix Ratio By Weight100A:29B
Pot Life5 minutes22 minutes
Thin Film Working Time90 minutes
Cure Time45 minutes15 hours
Shore D Hardness80
Shore A Hardness22
Specific Gravity1.08 g/cc1.11 g/cc
Specific Volume25.6 cu. in./lb.25 cu. in./lb.
ColorTranslucent GreenClear Yellow
Die B Tear Strength102 pli
Tensile Strength490 psi
Tensile Modulus450,000 psi
Ultimate Tensile8,180 psi
Tensile Elongation3.15 %
Elongation @ Break450 %
100% Modulus49 psi
Compressive Strength10,970 psi
Compressive Modulus122,000 psi
Flexural Strength12,220 psi
Flexural Modulus423,000 psi
Shrinkage<.001 in. / in.
Heat Deflection Temp120 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F
Flexural Strength on 6 ply / 10 oz. Laminate28,500 psi
Ultimate Tensile on 6 ply / 10 oz. Laminate26,800 psi

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

EpoxAmite™ 102

EpoxAmite™ 102 is an easy-to-use liquid epoxy system formulated for a wide variety of fabrication applications. EpoxAmite™ 102 includes the EpoxAmite™ 100 Base and the EpoxAmite™ 102 MEDIUM Hardener.  EpoxAmite™ 102 is unfilled, low in viscosity, odorless and cures at room temperature. Cured epoxy displays exceptional physical and performance properties. It can be sanded, shaped, machined, drilled, tapped and painted.

EpoxAmite™ 102 can be used with reinforcements such as S-Glass, E-Glass, Kevlar and Carbon fibers for lay-up applications or composite parts. EpoxAmite™ 102 can also be mixed with fillers such as fumed silica for gel coat applications. Urefil™ 3, Urefil™ 7 and other fillers can be added for fairing, filleting or bonding applications.

Applications: Wet Lay-Up Lamination, General Bonding & Repair, Clear Coating - Gel Coating, Barrier Coating, Thin-Section Casting, Water Proofing, Patching & Small Laminates 

Also available: EpoxAmite™ 101 FAST SET and EpoxAmite™ 103 SLOW SET 

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›