Compare Tool

Vs.
remove

EpoxAmite™ 103

EpoxAmite™ 103 vs. EZ-Spray® Silicone 22EZ-Spray® Silicone 22

SLOW Cure Epoxy Laminating System

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
Mixed Viscosity11,000 cps650 cps
Pot Life5 minutes55 minutes
Cure Time45 minutes24 hours
Shore D Hardness80
Shore A Hardness22
ColorTranslucent GreenClear Yellow
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22EpoxAmite™ 103
Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
Mixed Viscosity11,000 cps650 cps
Mix Ratio By Volume1A:1B3A:1B
Mix Ratio By Weight100A:28.4B
Pot Life5 minutes55 minutes
Thin Film Working Time180 minutes
Cure Time45 minutes24 hours
Shore D Hardness80
Shore A Hardness22
Specific Gravity1.08 g/cc1.10 g/cc
Specific Volume25.6 cu. in./lb.25.2 cu. in./lb.
ColorTranslucent GreenClear Yellow
Die B Tear Strength102 pli
Tensile Strength490 psi
Tensile Modulus452,000 psi
Ultimate Tensile7,910 psi
Tensile Elongation2.63 %
Elongation @ Break450 %
100% Modulus49 psi
Compressive Strength10,500 psi
Compressive Modulus104,000 psi
Flexural Strength12,300 psi
Flexural Modulus429,000 psi
Shrinkage<.001 in. / in.
Heat Deflection Temp127 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F
Flexural Strength on 6 ply / 10 oz. Laminate20,700 psi
Ultimate Tensile on 6 ply / 10 oz. Laminate27,000 psi

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

EpoxAmite™ 103

EpoxAmite™ 103 is an easy-to-use liquid epoxy system formulated for a wide variety of fabrication applications. EpoxAmite™ 103 includes the EpoxAmite™ 100 Base and the EpoxAmite™ 103 SLOW Hardener.  EpoxAmite™ 103 is unfilled, low in viscosity, odorless and cures at room temperature. Cured epoxy displays exceptional physical and performance properties. It can be sanded, shaped, machined, drilled, tapped and painted.

EpoxAmite™ 103 can be used with reinforcements such as S-Glass, E-Glass, Kevlar and Carbon fibers for lay-up applications or composite parts. EpoxAmite™ 101 can also be mixed with fillers such as fumed silica for gel coat applications. Urefil™ 3, Urefil™ 7 and other fillers can be added for fairing, filleting or bonding applications.

Applications: Wet Lay-Up Lamination, General Bonding & Repair, Clear Coating - Gel Coating, Barrier Coating, Thin-Section Casting, Water Proofing, Patching & Small Laminates 

Also available: EpoxAmite™ 101 FAST SET and EpoxAmite™ 102 MEDIUM SET 

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›