Compare Tool

Vs.

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
Mix Ratio By Volume1A:1BN/A (gram scale required)
Pot Life5 minutes4 hours
Cure Time45 minutes24 hours
Shore D Hardness90
Shore A Hardness22
Specific Volume25.6 cu. in./lb.16.5 cu. in./lb.
ColorTranslucent GreenGrey
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22EpoxAcast™ 655 + HT Hardener
Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
Mixed Viscosity11,000 cps12,000 cps
Mix Ratio By Volume1A:1B
Mix Ratio By Weight100A:8B
Pot Life5 minutes4 hours
Cure Time45 minutes24 hours
Shore D Hardness90
Shore A Hardness22
Specific Gravity1.08 g/cc1.64 g/cc
Specific Volume25.6 cu. in./lb.16.5 cu. in./lb.
ColorTranslucent GreenGrey
Die B Tear Strength102 pli
Tensile Strength490 psi
Tensile Modulus7,200,000 psi
Ultimate Tensile6,000 psi
Elongation @ Break450 %
100% Modulus49 psi
Compressive Strength15,700 psi
Compressive Modulus270,000 psi
Flexural Modulus1,403,000 psi
Shrinkage<.001 in. / in.0.001 in. / in.
Heat Deflection Temp225 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

EpoxAcast™ 655 + HT Hardener

EpoxAcast™ 655 (formerly Metalset™ A-30) is a versatile aluminum filled castable epoxy that is very hard and strong. It is dimensionally stable, even when mass cast up to 512 in3 / 8,390 cm3. Maximum heat resistance is achieved using HT HIGH TEMP hardener (up to 225°F/108°C).

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›