Compare Tool

Vs.
remove

EpoxAcast™ 650 BLACK + HT Hardener

EZ-Spray® Silicone 22 vs. EpoxAcast™ 650 BLACK + HT HardenerEZ-Spray® Silicone 22

Mineral filled general purpose casting epoxy

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
Mixed Viscosity11,000 cps5,000 cps
Mix Ratio By Volume1A:1BN/A (gram scale required)
Pot Life5 minutes3 hours
Cure Time45 minutes24 hours
Barcol 935 Hardness93
Shore A Hardness22
Specific Volume25.6 cu. in./lb.18.22 cu. in./lb.
ColorTranslucent GreenBlack
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22EpoxAcast™ 650 BLACK + HT Hardener
Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
Mixed Viscosity11,000 cps5,000 cps
Mix Ratio By Volume1A:1B
Mix Ratio By Weight100A:10B
Pot Life5 minutes3 hours
Cure Time45 minutes24 hours
Barcol 935 Hardness93
Shore A Hardness22
Specific Gravity1.08 g/cc1.52 g/cc
Specific Volume25.6 cu. in./lb.18.22 cu. in./lb.
ColorTranslucent GreenBlack
Die B Tear Strength102 pli
Tensile Strength490 psi
Tensile Modulus1,079,000 psi
Ultimate Tensile6,900 psi
Elongation @ Break450 %
100% Modulus49 psi
Compressive Strength15,980 psi
Compressive Modulus134,000 psi
Flexural Strength10,850 psi
Flexural Modulus775,000 psi
Shrinkage<.001 in. / in.0.007 in. / in.
Heat Deflection Temp187 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

EpoxAcast™ 650 BLACK + HT Hardener

EpoxAcast™ 650 Black is a mineral filled general purpose casting epoxy that is low cost and versatile. It features a low mixed viscosity for minimal bubble entrapment.EpoxAcast™ 650 Black is used for making hard dies for metal stamping as well as patterns and fixtures. It is also used for electrical encapsulation to extend the life cycles and enhance the performance of potted electronic devices. The high compressive strength of EpoxAcast™ 650 Black makes it ideal for making stamping dies for production pressing of metal ornaments.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›