Compare Tool

Vs.
remove

Clear Flex™ 95

Clear Flex™ 95 vs. EZ-Spray® Silicone 22EZ-Spray® Silicone 22

Water Clear Urethane Rubber

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Rubber
Mixed Viscosity11,000 cps250 cps
Pot Life5 minutes25 minutes
Cure Time45 minutes16 hours
Shore A Hardness2295
ColorTranslucent GreenClear
Tensile Strength490 psi2,500 psi
Elongation @ Break450 %175 %
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22Clear Flex™ 95
Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Rubber
Mixed Viscosity11,000 cps250 cps
Mix Ratio By Volume1A:1BN/A
Mix Ratio By Weight1A:1.5B
Pot Life5 minutes25 minutes
Cure Time45 minutes16 hours
Shore A Hardness2295
Specific Gravity1.08 g/cc1.04 g/cc
Specific Volume25.6 cu. in./lb.26.8 cu. in./lb.
ColorTranslucent GreenClear
Die B Tear Strength102 pli
Die C Tear Strength200 pli
Tensile Strength490 psi2,500 psi
Elongation @ Break450 %175 %
100% Modulus49 psi
Shrinkage<.001 in. / in.0.0028 in. / in.
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F
Volume Resistivity>6.014E+15 ohm/cm
Volume Resistance>7.646E+13 ohm
Dielectric Constant, 100Hz6.62
Dielectric Strength474 volts/mil
Dissipation Factor, 100Hz0.103

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

Clear Flex™ 95

Clear Flex™ 95 is a water white clear urethane liquid rubber compounds designed for applications that require absolute clarity and resistance to sunlight. Low viscosity ensures easy mixing and pouring. Clear Flex™ 95 cures at room temperature with negligible shrinkage.

CAUTION: NOT FOR HOME USE. THIS PRODUCT IS FOR INDUSTRIAL USE ONLY. With adequate local exhaust ventilation, respiratory protection is not normally required when using this product. Where risk assessment shows air-purifying respirators are appropriate, follow OSHA respirator regulations and European Standards EN 141, 143 and 371. Protective clothing (gloves and long sleeves) is required to minimize the risk of dermal sensitization. If breathing is affected or a dermal rash develops, immediately cease using this product and seek medical attention. Read SDS before using.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›