Compare Tool

Vs.
remove

Smooth-Cast® 380

Smooth-Cast® 380 vs. EZ-Spray® Silicone 22EZ-Spray® Silicone 22

High Density Urethane Tooling Resin

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Resins
Mixed Viscosity11,000 cps1,140 cps
Cure Time45 minutes60 minutes
Shore D Hardness82
Shore A Hardness22
Specific Volume25.6 cu. in./lb.15.9 cu. in./lb.
ColorTranslucent GreenTan
Tensile Strength490 psi3,550 psi
Elongation @ Break450 %1.43 %
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

EZ-Spray® Silicone 22Smooth-Cast® 380
Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Resins
Mixed Viscosity11,000 cps1,140 cps
Mix Ratio By Volume1A:1B1A:1B
Mix Ratio By Weight1A:1B
Pot Life5 minutes6 minutes
Cure Time45 minutes60 minutes
Shore D Hardness82
Shore A Hardness22
Specific Gravity1.08 g/cc1.74 g/cc
Specific Volume25.6 cu. in./lb.15.9 cu. in./lb.
ColorTranslucent GreenTan
Die B Tear Strength102 pli
Tensile Strength490 psi3,550 psi
Tensile Modulus490,000 psi
Elongation @ Break450 %1.43 %
100% Modulus49 psi
Compressive Strength7,860 psi
Compressive Modulus126,000 psi
Flexural Strength4,870 psi
Flexural Modulus315,000 psi
Shrinkage<.001 in. / in.0.0025 in. / in.
Heat Deflection Temp125 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)500 °F

Product Description

EZ-Spray® Silicone 22

EZ~Spray® Silicone 22 are sprayable silicones which cure quickly to soft rubbers with high elongation and tear strength. Liquid silicone is sprayed through the EZ~Spray® Junior Cartridge System which is an economical alternative to expensive spray equipment. After a suitable thickness is attained, EZ~Spray® Silicone 22 cures in about 45 minutes. EZ~Spray® Silicone cures with negligible shrinkage to strong, durable silicone rubbers good for production casting of polyester, epoxy or urethane resins, gypsum, concrete and other materials.

Read More

Smooth-Cast® 380

Smooth-Cast® 380 is a filled, high density casting resin formulated for a variety of tooling applications. This no-odor resin features a convenient 1A:1B mix ratio by volume, a 6 minute pot-life and cure time of about 60 minutes depending on mass and temperature. Low viscosity ensures minimal bubble entrapment and long term shrinkage of cured resin is very low. Cured material is very strong can be machined, drilled, sanded, etc. Color can be added with SO-Strong® color tints.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›