Compare Tool

remove

Ecoflex™ 5

Ecoflex™ 5 vs. EZ-Spray® 45

Super-Soft, Addition Cure Silicone Rubber

 View Product

Vs.
remove

EZ-Spray® 45

Ecoflex™ 5 vs. EZ-Spray® 45Ecoflex™ 5

Sprayable Urethane Rubber Compound

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Rubber
Mixed Viscosity13,000 cpsSprayable
Pot Life1 minute20 minutes
Cure Time5 minutes16 hours
Shore A Hardness545
ColorTranslucentLight Blue
Tensile Strength350 psi510 psi
Elongation @ Break1,000 %375 %
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

Ecoflex™ 5EZ-Spray® 45
Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Rubber
Mixed Viscosity13,000 cpsSprayable
Mix Ratio By Volume1A:1B1A:1B
Mix Ratio By Weight1A:1B
Pot Life1 minute20 minutes
Cure Time5 minutes16 hours
Shore A Hardness545
Specific Gravity1.07 g/cc1.025 g/cc
Specific Volume25.8 cu. in./lb.27 cu. in./lb.
ColorTranslucentLight Blue
Die B Tear Strength75 pli
Die C Tear Strength100 pli
Tensile Strength350 psi510 psi
Elongation @ Break1,000 %375 %
100% Modulus15 psi
Shrinkage<.001 in. / in.<.001 in. / in.
Useful Temperature (min)-65 °F
Useful Temperature (max)450 °F

Product Description

Ecoflex™ 5

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage.  Low viscosity ensures easy mixing and de-airing. Dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion.

Read More

EZ-Spray® 45

EZ~Spray® 45 is a polyurethane rubber for spraying through the EZ~Spray® Junior Cartridge System. Refer to EZ~Spray® Junior manual prior to spraying this product. EZ~Spray® 45 can be sprayed onto vertical surfaces for making molds or is good for making fast molds of large surface areas. After a suitable thickness is attained, EZ~Spray® 45 cures overnight with negligible shrinkage to a durable mold rubber. Application of a support shell is achieved by spraying Smooth-On’s EZ~Spray® Plastic over the rubber mold after it has fully cured. EZ~Spray® 45 is suitable for casting a variety of materials including wax, gypsum, urethane or epoxy resins, concrete, etc.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›