Compare Tool

remove

Ecoflex™ 5

Ecoflex™ 5 vs. Plasti-Paste® II vs. EpoxAcast™ 650 + 102 Hardener

Super-Soft, Addition Cure Silicone Rubber

 View Product

Vs.
remove

EpoxAcast™ 650 + 102 Hardener

Ecoflex™ 5 vs. Plasti-Paste® II vs. EpoxAcast™ 650 + 102 HardenerEcoflex™ 5

Mineral Filled General Purpose Casting Epoxy

 View Product

Vs.

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
  • Urethane Resins
Mixed Viscosity13,000 cps7,000 cpsLight Paste
Mix Ratio By Volume1A:1BN/A (gram scale required)1A:2B
Pot Life1 minute90 minutes10 minutes
Cure Time5 minutes4 hours90 minutes
Barcol 935 Hardness93
Shore D Hardness70
Shore A Hardness5
Specific Volume25.8 cu. in./lb.18.22 cu. in./lb.27.73 cu. in./lb.
ColorTranslucentOff WhiteOff White
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

Ecoflex™ 5EpoxAcast™ 650 + 102 HardenerPlasti-Paste® II
Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy Casting and Laminating Resins
  • Urethane Resins
Mixed Viscosity13,000 cps7,000 cpsLight Paste
Mix Ratio By Volume1A:1B1A:2B
Mix Ratio By Weight1A:1B100A:13B62A:100B
Pot Life1 minute90 minutes10 minutes
Cure Time5 minutes4 hours90 minutes
Barcol 935 Hardness93
Shore D Hardness70
Shore A Hardness5
Specific Gravity1.07 g/cc1.52 g/cc1.0 g/cc
Specific Volume25.8 cu. in./lb.18.22 cu. in./lb.27.73 cu. in./lb.
ColorTranslucentOff WhiteOff White
Die B Tear Strength75 pli
Tensile Strength350 psi
Tensile Modulus1,503,000 psi235,000 psi
Ultimate Tensile6,000 psi2,150 psi
Elongation @ Break1,000 %1.14 %
100% Modulus15 psi
Compressive Strength16,350 psi4,980 psi
Compressive Modulus142,600 psi62,700 psi
Flexural Strength5,890 psi3,840 psi
Flexural Modulus710,000 psi203,000 psi
Shrinkage<.001 in. / in.0.001 in. / in.0.005 in. / in.
Heat Deflection Temp129 °F130 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)450 °F

Product Description

Ecoflex™ 5

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage.  Low viscosity ensures easy mixing and de-airing. Dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion.

Read More

EpoxAcast™ 650 + 102 Hardener

EpoxAcast™ 650 is a mineral filled general purpose casting epoxy that is low cost and versatile. It features a low mixed viscosity for minimal bubble entrapment.

Read More

Plasti-Paste® II

New Plasti-Paste® II is a two component fiber-filled resin that is designed for vertical surface application. This no-odor formulation is an improved version of our original Plasti-Paste® formula, and the cured product is different in the following ways:

  1. Plasti-Paste II is now phthalate free.
  2. Cured plastic can be painted (original Plasti Paste® can not)
  3. It is harder, more rigid with better heat resistance.

Part A is a liquid and Part B is a paste. New Mix Ratio is 1A: 2B by volume (62A:100B by weight). Pot life is 10 minutes at room temperature depending on mass. Demold time (can be handled) is about 90 minutes at room temperature depending on mass. Full cure; 24 hours at room temperature. Cure time can be accelerated by applying heat.

Mixed material holds a vertical surface without sagging and cures to a strong, durable and lightweight plastic. Liquid material can be pigmented with So-Strong® color tints from Smooth-On. This plastic can be used for creating themed environments or special effects, used as a “mother mold” material to reinforce rubber molds and a variety of other applications. This plastic is also a powerful adhesive and can be used as a repair material for a variety of industrial applications. Cured plastic can be sanded, machined and painted with acrylic enamel paints.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›