Compare Tool

remove

Ecoflex™ 5

Rubber Glass™ vs. Ecoflex™ 5 vs. Epsilon™ PRO

Super-Soft, Addition Cure Silicone Rubber

 View Product

Vs.
remove

Epsilon™ PRO

Rubber Glass™ vs. Ecoflex™ 5 vs. Epsilon™ PROEcoflex™ 5

High Performance Impact Resistant EPS Foam Coating

 View Product

Vs.
remove

Rubber Glass™

Rubber Glass™ vs. Ecoflex™ 5 vs. Epsilon™ PROEcoflex™ 5 versus Epsilon™ PRO

For Flexible Fake Glass & Ice Effects

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy and Urethane Coatings
  • Silicone Rubber - Platinum Cure
Mixed Viscosity13,000 cps4,000 cps150 cps
Pot Life1 minute22 minutes120 minutes
Cure Time5 minutes16 hours16 hours
Shore D Hardness65
Shore A Hardness533
ColorTranslucentClear AmberClear
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

Ecoflex™ 5Epsilon™ PRORubber Glass™
Product Type
  • Silicone Rubber - Platinum Cure
  • Epoxy and Urethane Coatings
  • Silicone Rubber - Platinum Cure
Mixed Viscosity13,000 cps4,000 cps150 cps
Mix Ratio By Volume1A:1B2A:1B1A:1B
Mix Ratio By Weight1A:1B100A:44B1A:1B
Pot Life1 minute22 minutes120 minutes
Thin Film Working Time35 minutes
Thin Film Recoat Time3 hours
Cure Time5 minutes16 hours16 hours
Shore D Hardness65
Shore A Hardness533
Specific Gravity1.07 g/cc1.11 g/cc0.97 g/cc
Specific Volume25.8 cu. in./lb.25.0 cu. in./lb.28.6 cu. in./lb.
ColorTranslucentClear AmberClear
Die B Tear Strength75 pli
Tensile Strength350 psi
Elongation @ Break1,000 %
100% Modulus15 psi
Shrinkage<.001 in. / in.<.001 in. / in.
Useful Temperature (min)-65 °F
Useful Temperature (max)450 °F
Dielectric Strength319 volts/mil
Dielectric Constant, 100Hz3.17

Product Description

Ecoflex™ 5

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage.  Low viscosity ensures easy mixing and de-airing. Dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion.

Read More

Epsilon™ PRO

Epsilon™ PRO is a thixotropic epoxy coating that self-thickens for brushing onto a variety of surfaces.  Compared to original Epsilon™, Epsilon™ PRO offers a longer working time and cured epoxy is semi-rigid, offering better impact resistance.  Mix ratio for Epsilon™ PRO is 2A:1B by volume (100A:44B by weight).  A gram scale is not needed to use this product.

Applied in thin layers, mixed material holds a vertical surface without sagging or slumping. Material wets out uniformly over different surfaces.  Pot life is 22 minutes, with a re-coat time of 3 hours.  All layers should be allowed to cure for 16 hours at 73° F / 23° C and can be accelerated with mild heat.  Epsilon™ PRO is clear and can be easily colored using Ignite™ or UVO™ colorants.  Cured coating has a gloss finish and can be sanded, primed and painted.

Applications: Epsilon™ PRO is suitable for use as a protective, impact resistant coating for EPS or polyurethane foam. It can also be applied to plaster, concrete, wood and fabrics. This product is not sensitive to moisture / humidity and contains no VOC’s. 

Read More

Rubber Glass™

Rubber Glass™ is a platinum-catalyzed silicone rubber product developed specifically for special effects and display applications. Two liquids (1 Part A + 1 Part B) are mixed together and poured into a container.

The mixture cures overnight to a solid water clear rubber that can then be easily broken or “crumbled” into pieces that look exactly like broken glass, ice or diamonds. Vibrant colors are possible by adding Silc-Pig™ liquid color pigments.

Rubber Glass™ can be used to create a variety of special effects (i.e. simulated broken glass where human contact is required) and model effects (i.e. simulated ice or water). It can also be used for electronic encapsulation applications.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›