Compare Tool

remove

Ecoflex™ 5

Ecoflex™ 5 vs. Smooth-Cast® 310 vs. EpoxAcoat™ HT

Super-Soft, Addition Cure Silicone Rubber

 View Product

Vs.
remove

Smooth-Cast® 310

Ecoflex™ 5 vs. Smooth-Cast® 310 vs. EpoxAcoat™ HTEcoflex™ 5

Bright White, Ultra Low Viscosity Liquid Plastics

 View Product

Vs.
remove

EpoxAcoat™ HT

Ecoflex™ 5 vs. Smooth-Cast® 310 vs. EpoxAcoat™ HTEcoflex™ 5 versus Smooth-Cast® 310

High Temp Surface Coat Epoxy

 View Product

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Resins
  • Epoxy Casting and Laminating Resins
  • Epoxy and Urethane Coatings
Mixed Viscosity13,000 cps80 cpsLight Paste
Mix Ratio By Volume1A:1B1A:1BN/A (gram scale required)
Pot Life1 minute20 minutes40 minutes
Cure Time5 minutes4 hours24 hours
Shore D Hardness7085
Shore A Hardness5
ColorTranslucentWhiteDark Red
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

Ecoflex™ 5Smooth-Cast® 310EpoxAcoat™ HT
Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Resins
  • Epoxy Casting and Laminating Resins
  • Epoxy and Urethane Coatings
Mixed Viscosity13,000 cps80 cpsLight Paste
Mix Ratio By Volume1A:1B1A:1B
Mix Ratio By Weight1A:1B100A:90B100A:18B
Pot Life1 minute20 minutes40 minutes
Thin Film Working Time75 minutes
Thin Film Recoat Time4 hours
Cure Time5 minutes4 hours24 hours
Shore D Hardness7085
Shore A Hardness5
Specific Gravity1.07 g/cc1.05 g/cc
Specific Volume25.8 cu. in./lb.26.4 cu. in./lb.
ColorTranslucentWhiteDark Red
Die B Tear Strength75 pli
Tensile Strength350 psi3,000 psi
Tensile Modulus134,000 psi
Elongation @ Break1,000 %7.5 %
100% Modulus15 psi
Compressive Strength3,800 psi
Compressive Modulus44,900 psi
Flexural Strength4,000 psi
Flexural Modulus118,000 psi
Shrinkage<.001 in. / in.0.0065 in. / in.
Heat Deflection Temp120 °F133 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)450 °F
Heat Deflection With Post Cure284 °F

Product Description

Ecoflex™ 5

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage.  Low viscosity ensures easy mixing and de-airing. Dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion.

Read More

Smooth-Cast® 310

The Smooth-Cast® 300 Series of liquid plastics are ultra-low viscosity casting resins that yield castings that are bright white and virtually bubble free. Vacuum degassing is not necessary. They offer the convenience of a 1A:1B by volume or 100A:90B by weight mix ratio. The differences between them are pot life and demold time.

These resins readily accept fillers (such as URE-FIL® 3 from Smooth-On) and can be colored with SO-Strong® or Ignite® color tints (Smooth-Cast® 325 series accepts pigments better than the Smooth Cast® 300 series). Fully cured castings are tough, durable, machinable and paintable. They resist moisture and mild solvents. Applications for Smooth-Cast® 300 Series Liquid Plastics include reproducing small to medium size sculptures, making prototype models, special effect props and decorative jewelry.

Read More

EpoxAcoat™ HT

EpoxAcoat™ HT is a slightly thixotropic epoxy gel coat that offers high heat resistance (post cure required).  Cured epoxy is tough and offers exceptional abrasion resistance.  This surface coat will wet out well over a variety of surfaces with good sag resistance.  Applications include laminating, precision tooling, master and pattern making, core boxes and fixtures.
Use as a surface coat for EpoxAmite™ HT high temperature laminating epoxy.

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›