Compare Tool

remove

Ecoflex™ 5

Ecoflex™ 5 vs. Smooth-Cast® ONYX™ FAST vs. EpoxAcast™ 655 + HT Hardener

Super-Soft, Addition Cure Silicone Rubber

 View Product

Vs. Vs.

Add Material to Compare

start over

Key Differences

Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Resins
  • Epoxy Casting and Laminating Resins
Mixed Viscosity13,000 cps100 cps12,000 cps
Mix Ratio By Volume1A:1B100A:100BN/A (gram scale required)
Pot Life1 minute2.5 minutes4 hours
Cure Time5 minutes15 minutes24 hours
Shore D Hardness8090
Shore A Hardness5
Specific Volume25.8 cu. in./lb.27.7 cu. in./lb.16.5 cu. in./lb.
ColorTranslucentBlackGrey
Disclaimer
Although we do our best to ensure the accuracy of this Compare Tool, Smooth-On offers no warranty either expressed or implied as to the reliability of the information contained herein. Smooth-On assumes no liability for loss or damage associated with use of the Compare Tool. If this is a critical project, we encourage you to review all of the technical data below and contact our Technical Service department with any questions or concerns.

All Technical Data

Ecoflex™ 5Smooth-Cast® ONYX™ FASTEpoxAcast™ 655 + HT Hardener
Product Type
  • Silicone Rubber - Platinum Cure
  • Urethane Resins
  • Epoxy Casting and Laminating Resins
Mixed Viscosity13,000 cps100 cps12,000 cps
Mix Ratio By Volume1A:1B100A:100B
Mix Ratio By Weight1A:1B120A:100B100A:8B
Pot Life1 minute2.5 minutes4 hours
Cure Time5 minutes15 minutes24 hours
Shore D Hardness8090
Shore A Hardness5
Specific Gravity1.07 g/cc1.09 g/cc1.64 g/cc
Specific Volume25.8 cu. in./lb.27.7 cu. in./lb.16.5 cu. in./lb.
ColorTranslucentBlackGrey
Die B Tear Strength75 pli
Tensile Strength350 psi5,840 psi
Tensile Modulus246,000 psi7,200,000 psi
Ultimate Tensile6,000 psi
Elongation @ Break1,000 %4 %
100% Modulus15 psi
Compressive Strength8,760 psi15,700 psi
Compressive Modulus77,400 psi270,000 psi
Flexural Strength8,280 psi
Flexural Modulus246,000 psi1,403,000 psi
Shrinkage<.001 in. / in.0.010 in. / in.0.001 in. / in.
Heat Deflection Temp225 °F
Useful Temperature (min)-65 °F
Useful Temperature (max)450 °F
Heat Deflection With Post Cure250 °F

Product Description

Ecoflex™ 5

Ecoflex™ rubbers are platinum-catalyzed silicones that are versatile and easy to use. Ecoflex™ rubbers are mixed 1A:1B by weight or volume and cured at room temperature with negligible shrinkage.  Low viscosity ensures easy mixing and de-airing. Dispense using our convenient dispensing cartridges. Cured rubber is very soft, very strong and very “stretchy”, stretching many times its original size without tearing and will rebound to its original form without distortion.

Read More

Smooth-Cast® ONYX™ FAST

Smooth-Cast® ONYX™ is a mercury-free urethane resin that cures at room temperature to a deep black, solid plastic. ONYX™ resins offer the convenience of a 1A:1B by volume mix ratio and have very low viscosities, so they are easy to mix and pour. ONYX™ resins have an ultimate Shore hardness of 80D and offer higher physical properties and higher heat resistance vs. other general purpose resins.ONYX™ FAST resin has a pot life of 2.5 minutes and a cure time of 10-15 minutes. ONYX™ FAST is a good choice for creating fast cold cast bronze, brass, copper, nickel/silver, etc. effects.

Read More

EpoxAcast™ 655 + HT Hardener

EpoxAcast™ 655 (formerly Metalset™ A-30) is a versatile aluminum filled castable epoxy that is very hard and strong. It is dimensionally stable, even when mass cast up to 512 in3 / 8,390 cm3. Maximum heat resistance is achieved using HT HIGH TEMP hardener (up to 225°F/108°C).

Read More

Select a Material from a Category Below

Silicone Rubber - Tin Cure ›

Silicone Rubber - Platinum Cure ›

Urethane Rubber ›

Polysulfide Rubber ›

Urethane Resins ›

Epoxy Casting and Laminating Resins ›

Epoxy Putties ›

Epoxy and Urethane Coatings ›

Mix and Pour Expanding Foams ›

Adhesives ›

Lifecasting Materials ›

Skin Safe FX Materials ›

Polymer Modifiers for Concrete and Gypsum ›