C
mpare
T
l
Key Differences
| Product Type |
|
|
| Mixed Viscosity | 300 cps | 100 cps |
| Pot Life | 1.5 minutes | 20 minutes |
| Cure Time | 2 hours | 4 hours |
| Shore D Hardness | — | 72 |
| Specific Volume | 420 cu. in./lb. | 25.9 cu. in./lb. |
| Color | Black | Clear Amber |
Disclaimer
Although we do our best to ensure accuracy, Smooth-On offers no warranties, promises, and/or representations of any kind, either expressed or implied, as to the accuracy, completeness, or reliability of the information contained on this Compare Tool, nor suitability of the information contained herein to your particular circumstances. Smooth-On assumes no liability for losses or damages of whatever nature (direct, indirect, consequential or other) associated with your use, or inability to use, the Compare Tool, or from your use (or failure to use) the information contained herein. Other useful tools include product technical bulletins and our extensive FAQ section. You can also contact our technical support team.All Technical Data
| FOAM-iT!™ 4 BLACK | Smooth-Cast™ 327 | |
|---|---|---|
| Product Type |
|
|
| Mixed Viscosity | 300 cps | 100 cps |
| Mix Ratio By Volume | 1A:1B | 1A:1B |
| Mix Ratio By Weight | 100A:87B | 115A:100B |
| Pot Life | 1.5 minutes | 20 minutes |
| Tack Free Time | 20 minutes | — |
| Cure Time | 2 hours | 4 hours |
| Shore D Hardness | — | 72 |
| Expansion (approximate) | 14 times | — |
| Foam Density | 4 lb/ft³ | — |
| Specific Gravity | 0.06 g/cc | 1.07 g/cc |
| Specific Volume | 420 cu. in./lb. | 25.9 cu. in./lb. |
| Color | Black | Clear Amber |
| Tensile Strength | — | 3,170 psi |
| Tensile Modulus | — | 140,000 psi |
| Elongation @ Break | — | 10 % |
| Compressive Strength | — | 3,080 psi |
| Compressive Modulus | — | 32,200 psi |
| Flexural Strength | — | 3,100 psi |
| Flexural Modulus | — | 95,700 psi |
| Shrinkage | — | 0.0075 in. / in. |
| Heat Deflection Temp | — | 120 °F |
Product Description
FOAM-iT!™ 4 BLACK
Smooth-On’s FOAM-iT!™ Series are two-component water blown rigid foams that are versatile and easy to use. FOAM-iT!™ products are available in 3lb., 4 lb., 5 lb., 8 lb., 10 lb.,15 lb. or 26 lb. per cubic foot densities. Parts A and B are measured and mixed in equal amounts by volume. The mixture is then poured into a mold or other form (apply release agent if necessary). The mixture will expand many times original volume (depending on which FOAM-iT!™ product you are using) and develop a uniform cell structure. FOAM-iT!™ 4 Black is pre-pigmented to a very deep black color.
All FOAM-iT!™ products can be used as a straight casting material, backfill material for hollow castings (adds structural strength) or as an encapsulation material, etc. They can be color pigmented with SO-Strong™, UVO™ or IGNITE™ colorants and are used for a variety of art/ craft, industrial design and special effects applications
› Click here for more FOAM-iT!™ rigid foam products.
Smooth-Cast™ 327
The Smooth-Cast™ 325, 326 & 327 ColorMatch™ Series plastics are fast-cast resins that were developed specifically for adding color pigments and fillers to achieve true color representation or filler effect. The ColorMatch™ Series is formulated “color neutral”. Small amounts of pigment will yield accurate, vivid colors from cured castings using So-Strong™ tints or Ignite™ color pigments. The ColorMatch™ Series offers the convenience of a 1A: 1B mix ratio by volume and has a very low viscosity. Demold times range from about 10 minutes to 2-4 hours (depending on product, mass and mold configuration). Note: Large mass castings will get very hot and shrink more, depending on mold configuration.
The ColorMatch™ Series also readily accept fillers (such as URE-FIL™ 3 from Smooth-On). Applications for the ColorMatch™ Series plastics include making pigmented prototype models or figures, special effect props, reproducing small to medium size sculptures, decorative jewelry, etc.