Mold Star™ 15 SLOW

Mold Star™ 15 SLOW *NOTE: Product Packaging May Vary

Mold Star™ rubbers are easy to use platinum silicones which are mixed 1A:1B by volume (no weighing scale necessary). Mold Star™ silicones feature relatively low viscosities and vacuum degassing is not required for most applications. The pot life of Mold Star™ 15 SLOW is 50 minutes and cure time is 4 hours at room temperature.

Features

Mold Star™ silicones cure to soft, strong rubbers which are tear resistant and exhibit very low long term shrinkage. Molds made with Mold Star™will last a long time in your mold library and are good for casting wax, gypsum, resins, and other materials. Cured Mold Star™ rubber is heat resistant up to 450°F (232°C) and is suitable for casting low-temperature melt metal alloys. Note: Mold Star™ rubbers are not intended for brush-on moldmaking.

Click here for more Mold Star™ silicone products.

Instructions

Note: This product will not cure against surfaces containing sulfur, even when sealed.

Safety - Use in a properly ventilated area (“room size” ventilation). Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Wear vinyl gloves only. Latex gloves will inhibit the cure of the rubber. Store and use material at room temperature (73°F/23°C). Warmer temperatures will drastically reduce working time and cure time. Storing material at warmer temperatures will also reduce the usable shelf life of unused material. These products have a limited shelf life and should be used as soon as possible.

Cure Inhibition - Addition cured silicone rubber may be inhibited by certain contaminants in or on the pattern to be molded resulting in tackiness at the pattern interface or a total lack of cure throughout the mold. Latex, sulfur clays, certain wood surfaces, newly cast polyester, epoxy or urethane rubber may cause inhibition. If compatibility between the rubber and the surface is a concern, a small-scale test is recommended. Apply a small amount of rubber onto a non-critical area of the pattern. Inhibition has occurred if the rubber is gummy or uncured after the recommended cure time has passed. To prevent inhibition, one or more coatings of a clear acrylic lacquer applied to the model surface is usually effective. Allow any sealer to thoroughly dry before applying rubber.

Even with a sealer, Mold Star™ silicones will not cure against surfaces containing sulfur. If you are not sure if your clay contains sulfur, do a small compatibility test before using for an important project.

Applying A Release Agent - Although not usually necessary, a release agent will make demolding easier when casting into most surfaces. Ease Release™ 200 is a proven release agent for releasing silicone from silicone or other surfaces. Mann Ease Release™ products are available from Smooth-On or your Smooth-On distributor.

Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Measuring & Mixing - Before you begin, pre-mix Part A and Part B separately. After dispensing required amounts of Parts A and B into mixing container (1A:1B by volume), mix thoroughly making sure that you scrape the sides and bottom of the mixing container several times. The rubber should be a uniform color with no streaks.

Optional... Vacuum Degassing - Although not necessary, vacuum degassing helps eliminate any entrapped air in pourable silicone rubber. After mixing parts A and B, vacuum material for 2-3 minutes at 29 inches of mercury, making sure that you leave enough room in container for product expansion.

Pouring - For best results, pour your mixture in a single spot at the lowest point of the containment field. Let the rubber seek its own level. A uniform flow will help minimize entrapped air. If using as a mold material, the liquid rubber should level off at least 1/2” (1.3 cm) over the highest point of the model surface.

Curing - Allow Mold Star™ 15 SLOW silicone rubber to cure for 4 hours at room temperature (73°F/23°C) before demolding.

Heat Curing - Time to demold can be reduced by applying mild heat. Example: After pouring Mold Star™ 15 rubber at room temperature, place the mold in a hot box or industrial oven at 140°F (60°C). This will reduce the time to demold of a 1/2” (1.3 cm) thick section to about 10 minutes. Note: Time will vary depending on mold thickness.

Adding an appropriate amount of Plat-Cat™ cure accelerator will also reduce demold time. The pot life and cure times can be extended using Slo-Jo™ cure retarder. Do not cure rubber where temperature is less than 65°F/18°C.

Mold Performance & Storage - The physical life of the mold depends on how you use it (materials cast, frequency, etc.). Casting abrasive materials can quickly erode mold detail, while casting non-abrasive materials (wax) will not affect mold detail. Before storing, the mold should be cleaned with a soap solution and wiped fully dry. Two part (or more) molds should be assembled. Molds should be stored on a level surface in a cool, dry environment.



Related Categories: Silicone Rubber - Platinum Cure

Related Series: Mold Star™ Series – Easy to Use Silicone Mold Rubber

How-To Articles

video

DIY Custom Valentine Candle Making Tutorial

DIY Custom Valentine Candle Making Tutorial

Learn how to easily make a custom candle.

 View How-To Article

video

Live! - Casting Silicone With Milo

Live! - Casting Silicone With Milo

Milo demonstrates how to cast silicone and explain how to choose the proper mold material for your application.

 View How-To Article

video

How To Make a Mold For Foam Cosplay Armor

How To Make a Mold For Foam Cosplay Armor

Learn how you can make a mold using Mold Star™ 15 silicone to cast FlexFoam-iT!™ 15 SLOW

 View How-To Article

video

How to Make a Silicone Mold of 3D Print

How to Make a Silicone Mold of 3D Print

This video demonstrates how to use Mold Star 20T to make a silicone mold of extruded PLA.

 View How-To Article

video

How To Make a Sea Anemone Using Smooth-On Silicone

How To Make a Sea Anemone Using Smooth-On Silicone

In this step-by-step gallery you will learn how to make a silicone sea anemone indistinguishable from the real thing

 View How-To Article

video

How To Make Finger Corals Using Smooth Cast™ Plastic

How To Make Finger Corals Using Smooth Cast™ Plastic

You can create perfect copies of any piece of original coral using mold rubber and liquid plastic.

 View How-To Article

video

Tutorial - How To Make a Silicone Christmas Tree Candle Mold

Tutorial - How To Make a Silicone Christmas Tree Candle Mold

In this video, Jeff demonstrates how to make a silicone mold for making candles and scented wax tarts.

 View How-To Article

video

How To Cast a Crystal Clear™ Shell in a Mold Star™ 15 Mold

How To Cast a Crystal Clear™ Shell in a Mold Star™ 15 Mold

This sequence demonstrates making a two piece silicone mold using Mold Star® 15 silicone rubber and Crystal Clear® 200

 View How-To Article

How To Make a 1 Piece Silicone Cut Mold

How To Make a 1 Piece Silicone Cut Mold

Mold Star® 15 is perfect for experienced mold makers or people just starting out.

 View How-To Article

video

How To Make a Silicone Mold Using Mold Star™ 15

How To Make a Silicone Mold Using Mold Star™ 15

Learn how to make a simple silicone mold using Mold Star™ 15 liquid silicone rubber.

 View How-To Article